Page Comparison

Display values

This value is displayed on line 1. This line is displayed in bold by default

In which unit is there to be registered in.

Note: This is a display value only as mobile does not know of item units. See Register Quantity By Scan

Basic information

Bin to Take items from

String

A list of barcodes identifying the item, e.g. Barcode1;Barcode2;Barcode3

Useful if items are packaged inside a box and the item barcodes are not visible unless the box is opened
Typically the box will have another barcode on it (because it’s a different unit of measure). If this barcode is also sent out it can be used to select the order line. 

Note:

• Mandatory for "RegisterQuantityByScan" to work See Select Line by scan (scanToSelectBehaviour)
• Scanning the barcodes can select an order line for the user

Semicolon separated
string list

Item number

Note: Scanning this, can select an order line for the user.

Quantity to register

Note: Mobile does not know the item units. See Register Quantity By Scan for another solution to this

Configuration

True: Quantity is collected by scanning one of the valid item barcodes.

Note: Requires "ItemBarcode"or "BarcodeQuantity" is specified. See See Register Quantity By Scan 

Special field to specify a RegEx - for barcode validation

Example: <BarcodeFormat>{[frombin][^\w{1,10}$]}</BarcodeFormat>

Field FromBin the barcode must be validated against the specified RegEx. String (RegEx), control field. Vaild fields to add regex: frombin, lot, serial, tobin, tote It it possible to specify multiple reg.ex for one field

Example: {[serial][regex1]}{[serial][regex2]}{[lot][regex3]}{[bin][regex4]}

See Barcode Quantity (enableMultiplier) for explanation

String, encoded

True: User is prompted for specifying serialnumber(s).
Each input/scan increments the registered quantity by one

Boolean

This is a control - to add extra steps to the current line.
Example: <RegisterExtraInfo>ReturnDisposition{[CauseId][defaultValue][51]}</RegisterExtraInfo>
It has a special setup, "ReturnDisposition" is a reference to a registrationCollectorConfiguration defined in GetReferenceData. The "CauseId" is a reference to a step in the collector - and "51" is the value to set. The field is not fully described here.
The collected values is returned in a "ExtraInfo" element per Line/Registration.

String

Use this element to have the registration collector return to a named step in the registration collector after performing a registration which is below the Quantity of the order line.
If set to LotNumber, and there is a remaining Quantity on the order line after completing a registration, the registration collector will not close, but return to the LotNumber step.

Boolean

If user registers a higher value than the suggested value in"Quantity", this setting determines the mobile behaviour.: 

None: User is allowed to register a higher/lower value

Warn: Warn the user if a higher/lower value than suggested is entered. A warning is displayed

Block: User is not allowed to register a higher/lower value. A error is displayed

See Register unexpected Quantity (overDeliveryValidation / underDeliveryValidation)

If user registers a lower value than the suggested value in"Quantity", this setting determines the mobile behaviour.: 

None: User is allowed to register a higher/lower value

Warn: Warn the user if a higher/lower value than suggested is entered. A warning is displayed

Block: User is not allowed to register a higher/lower value. A error is displayed

See Register unexpected Quantity (overDeliveryValidation / underDeliveryValidation)

True: User is prompted for specifying bin where items are taken

Note: Used with "FromBin":, control field

User must scan a value matching "FromBin" or if "FromBin" is blank,  the user can scan any value

Boolean

True: User is prompted for specifying Bin where items are placed

Note: Used with "ToBin":

User must scan a value matching "ToBin" or if "ToBin" is blank,  the user can scan any value

Step collection

Replaces the workflow defined for the planned service in application.cfg, with another workflow.
This can be done:

• either by referencing the id of another workflow defined in application.cfg
• or by sending out a complete workflow wrapped in a CDATA element

From version 1.8.0 the workflow configuration from the order line can be merged with the workflow defined in the service section. The key to merging instead of replacing is adding the attribute tweak="Append" to the registration collector configuration. <registrationCollectorConfiguration tweak="Append">

XML

This is an optional section, used to specify extra steps to perform after the "Post" has been choosen
These are also called "Header Steps". One collection is collected for all lines

See Whitepaper Understanding Steps

XML

Context

The quantity already registered. 

Note: This field always shows the same value as either "RegisteredQuantity" and "PlacedQuantity" 

The quantity already registered

Used when taking items

Decimal.

The quantity already registered

Used when placing items

Decimal.

Only Windows Handheld Embedded

The default behaviour of the mobile device when registering serial numbers is to assume a quantity of 1.
In some cases it may prove desirable to have a different quantity associated with the serial number.
Note: Replaced in Android by online validation serialnumber.